Skip to Content Skip to Left Navigation

Downspout Disconnect


Why Should I disconnect?
During a heavy storm, each downspout on your home can deliver 12 gallons a minute to the sewer system, which can contribute to basement backups and sewer overflows. By simply disconnecting a downspout, you can make a difference in keeping excess water out of the sewer system.

Who Should Disconnect?
Nearly Everyone!
Downspouts that are connected to the combined sewer system and any downspouts illegally connected to the sanitary sewer.

*It's VERY important to check with your municipality to make sure you can legally disconnect and that you disconnect correctly.

How?

All you need are a few supplies:
  • hacksaw
  • tape measure
  • hammer
  • screw driver
  • pliers
  • sheet metal screws
  • downspout elbow
  • downspout extension
  • splash block (optional)
  • rubber cap


Total cost per downspout should be less than $15.00

Step 1: Contact Your Municipality



Bayside 414-351-8811   Menomonee Falls 262-532-4700
Brookfield 262-782-9650   Mequon 262-242-3100
Brown Deer 414-357-0120   Muskego 262-679-4128
Butler 262-783-2530   New Berlin 262-786-7086
Caledonia 414-762-7878   Oak Creek 414-768-6547
Cudahy 414-769-2213   River Hills 414-352-0080
Elm Grove 262-782-6700   St. Francis 414-481-2300
Fox Point 414-351-8900   Shorewood 414-847-2640
Franklin 414-425-2592   Thiensville 262-242-3720
Germantown 262-250-4720   Wauwatosa 414-479-8932
Glendale 414-228-1710   West Allis 414-302-8379
Greendale 414-423-2133   West Milwaukee 414-645-6238
Greenfield 414-761-5376   Whitefish Bay 414-962-6690
Hales Corners 414-529-6161      


In the City Of Milwaukee:
To find out if your home is connected to the combined sewer call: 286-2480
To find out if you can legally disconnect call: 286-3361

Step 2
Measure 9" from where the downspout enters the sewer connection.



Step 3
Cut the downspout with a hacksaw.



Step 4
Cap the sewer standpipe. This prevents water from going in. In most cases, you should be able to use a simple rubber cap secured by hose clamp. You can also use a wing-nut test plug if available cap sizes don't fit.



Step 5
Insert the downspout INTO the elbow (if you put the elbow into the downspout, it will leak). You may need to crimp the end of the downspout with a pair of pliers to get a good fit.



Step 6
Attach a downspout pipe extension to carry water away from the house and foundation. You can use a hacksaw to cut the extension to the desired length. Be sure to insert the elbow into the extension to prevent leaks. Secure the elbow and extension with sheet metal screws. To prevent erosion where the water drains, you can place a splash block at the end of the downspout extension.






You're In Good Company

Across the country, cities have mandated that residents disconnect their downspouts from the sewer system. In Portland, Oregon, tens of thousands of homes disconnected, removing more than a million gallons of water from the sewerage system. That's valuable extra capacity and a very important step in reducing residential flooding. Disconnecting also helps keep our waterways clean by reducing the risk of a sewer overflow. For more information on similar programs and their successes, visit these Web sites:

Vancouver, Canada    www.cityfarmer.info

Toronto, Canada     www.city.toronto.on.ca

Portland, Oregon    www.portlandonline.com

Chicago, Illinois   www.cityofchicago.org